We've discovered this article about How to Install a Bathtub Yourself listed below on the web and felt it made perfect sense to relate it with you on my blog.
Mounting a tub isn't specifically rocket science, but it does call for solid plumbing, woodworking, and occasionally, tiling skills. Changing an old bath tub with a new one is likewise a moderately tough task. If the old tub is conveniently available, the task can move immediately; if you have to open up a wall surface to eliminate the old bathtub and place the brand-new bath tub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will require a helper to vacate the old tub and also set in the brand-new one. Ensure you have actually qualified on your own for the task and also are comfortable trying it. Instead of working with a professional to take control of a halfway-completed job, it is far better to consider utilizing one prior to you start. Chances are you might require a professional plumber to make tube connections.
This short article will certainly aid you install a new bath tub in your bathroom if you have already acquired a new tub as well as do not require to change the arrangement of your previous water system pipelines.
Your tools and material list need to comprise the following:
Preparing for the Installment
To start with, the sustaining structure provided with the bathroom must be fitted (if called for) according to the maker's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is essential to ensure that if the tap comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the taps device to stop pressure on the tub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you utilize every one of the provided washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to currently be ready to be fitted in its last placement.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any type of water continuing to be in the system. The procedure of eliminating the existing faucets can be fairly troublesome because of the restricted access that is frequently the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a towel prepared for the continuing to be water that will come from the pipes. As soon as the supply pipelines have been removed, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from turning throughout this process. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned of any kind of old sealing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the called for setting. The wood boards are valuable in equally spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four tiny points.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the bath tub till the spirit level reviews level.
To install faucets, fit the bottom of the outermost versatile tap adapter to the suitable supply pipe by making a compression sign up with; then do the same for the various other tap.
Switch on the water as well as check all joints and brand-new pipework for leaks and tighten them if needed. Fill the bath tub and additionally inspect the overflow outlet and also the typical outlet for leakages.
Finally, deal with the bathroom paneling as described in the maker's instruction manual. Tiling and also sealing around the bath tub ought to wait until the tub has actually been utilized at the very least once as this will certainly settle it right into its final placement.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and also the other end gives a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will need minimizing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the placing hole in the bath/basin making certain that the washers remain in area between the faucet and also the sink. Secure the faucet in position with the maker given backnut. Once the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular tap ports. The previous type ought to be attached to the faucet finishes initially, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bath satisfies the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to break an inflexible seal, causing the water to permeate the wall in between the bath and the tiling, causing complications with dampness and possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your components and also fittings. They are offered in tubes as well as cartridges, and also can sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly load the bathtub with water before sealing, to enable the motion experienced when the bathtub remains in usage. The sealer can crack fairly early if you do not take into consideration this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently offered on the market. It is recommended to fit the tiles using waterproof or water resistant sticky as well as grout.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter. Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches. Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains. Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris. Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run. If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.
Do you really like reading about How to Install a Bathtub Yourself? Write a short review below. We will be glad to hear your thinking about this entry. Hoping that you come back again in the near future. If you please take the opportunity to distribute this post if you appreciated it. I praise you for your time. Don't hesitate to come by our site back soon.
Get A Free Estimate